In private homes, cottages, sports complexes and hotels, they often use an indirect boiler - the water heater operates without being connected to a centralized water supply. This equipment copes with heating large volumes of water, easily maintains the desired temperature and ensures uninterrupted supply of a hot stream.
In a word, if you are looking for a budget water heater in the kit for a single-circuit boiler - consider installing in a BKN house. And to simplify the task of choice, we suggest that you familiarize yourself with the criteria for buying a boiler, the principle of its operation and connection schemes.
Design features and principle of operation of the BKN
Indirect heating boiler can only work on the resources of an external source, but for heating the system in the warm season, you can connect the heater.
In order to ensure uninterrupted supply, a recirculation loop is provided in the system - water will constantly move through the pipes, and when the tap is opened, a hot stream will flow at the points of draw-off connected to the loop.
Indirect heating boiler is usually installed next to the heating boiler, and this “duet” occupies a rather large area, especially if both devices are of floor type
Thus, the device can significantly save on energy resources, but at the same time get no less comfort than when using a centralized hot water supply system.
Image Gallery
Photo from
Equipment for the preparation of hot water
Connection pipes for communications
Bellows heat exchanger
Coils for installation in boiler tanks
Homemade Indirect Variant Option
Indirect gas cylinder water heater
Tying indirect heating boiler
Air bleeder
How is the indirect heating boiler arranged
A device that heats water according to an indirect principle. - This is an insulated storage tank, inside of which a heating element is installed, operating from an external coolant.
The tank itself can be made in the form of a rectangle or a cylinder, and nozzles are provided in its walls for circulating hot water from the heating system and the input / output of water pipes.
The design is based on a metal or plastic container with a capacity of ten to several thousand liters. From the inside, the tank can be coated with enamel, ceramic or glass porcelain, which helps to maintain proper water quality and avoid corrosion.
The housing is protected from heat loss by an insulating layer of polyurethane, foam rubber or mineral wool.
The coolant spiral can be evenly distributed over the entire tank, or fit tightly below to quickly heat the cold water entering there (+)
To prevent scale in the upper part of the tank, a magnesium or titanium anode is installed, which softens the water, protects the metal from galvanic corrosion and increases the life of the device.
The device is also equipped with a temperature regulator that controls heating to a certain temperature, and safety valves included in the protection group.
Pros and Cons of BKN
The main advantage of an indirect heating boiler is energy savings. For its operation, you do not need to connect a gas burner or use electricity, as the direct heating device requires.
The heating system provides all the necessary resources, so hot water is an almost free “bonus”, which will help to significantly save the family budget in the cold season.
Most indirect heating boilers are additionally equipped with heating elements with a temperature controller, so that you can use the device in the warm period when the heating is turned off
Other benefits of BKN:
- High performance - a tank with a volume of 100 liters is capable of “dispensing” about 400 liters of hot water per hour (provided a sufficiently powerful boiler is available).
- Long service life - the coolant does not come into contact with running water, as in similar direct heating devices.
- Does not overload the power grid - works from an external source of energy.
- Instant hot water - no need to wait until the cold stream flows, as when using gas columns, or the spent tank heats up, like an electric boiler.
- Affordable cost - If desired, the system can be assembled with your own hands.
- Ability to connect to multiple energy sourcesfor example, to a vacuum solar collector, boiler, geothermal heat pump.
Of course, there were some minuses here as well. With all its advantages, the speed of heating the water in the device leaves much to be desired - for the processing of 100 liters even modern equipment will spend at least 15-20 minutes, and home-made systems can not cope in an hour.
Also, indirect heating boilers are quite bulky, so they occupy an impressive amount of free space. Large tanks may require a separate room.
Indirect heating boiler can also be made from improvised materials using a bent copper pipe for the coil, a capacious barrel with a lid or a gas cylinder for the tank:
Image Gallery
Photo from
Steel tank boiler with lid
Bellows heat exchanger
Connection pipes for heating
Heat exchanger pipe fixing
Another option for a home-made indirect heating boiler is made using a casing from a conventional storage water heater:
Image Gallery
Photo from
The case from the storage water heater
Plastic pipe heat exchanger
Disk for connecting to the heating system
Installation of indirect heating boiler
In addition, this device will be truly economical only in the heating period, and in the warmer months you will have to either turn on the boiler or provide alternative heat sources - solar panels, heating elements. And the price of a high-quality “indirect man” exceeds analogues with direct heating.
Types and model varieties of equipment
The most common type of device is a storage tank, inside of which are placed steel or brass pipes (coil) with a circulating coolant.
The speed of heating the water depends on the number of turns on its spiral. The principle of operation of this design of an indirect heating boiler is extremely simple: cold water enters the tank, and the coolant, moving along the coil, heats it to the desired temperature.
But there are also devices designed according to the “tank in tank” scheme, where instead of a spiral pipeline two containers of different diameters are used.
The system works like this: cold water enters the smaller tank, which is heated by the hot coolant circulating between the walls of the tanks.
In such devices, the water becomes warm in a matter of minutes - a large heating area allows the equipment to operate efficiently in a flow mode, guaranteeing an uninterrupted supply of a hot stream.
Boilers operating on a “tank in tank” system not only quickly heat water to 90 ° C, but also have a self-cleaning function (+)
The combined BKN for heating water can use energy from several sources at once or be equipped with a built-in heating element.
Varieties of boiler KN
By placement:
- Wall - Usually, this is a small device with a displacement of up to 200 liters. It is fastened with special brackets to any vertical surface strong enough to support the weight of a completely filled tank (plasterboard partitions definitely will not work). It can be located high enough and not occupy the useful area of the room.
- Floor - a capacious boiler designed for a large number of consumers. True, for a device with a capacity exceeding 1000 l, it is recommended to allocate a separate room - to equip a boiler room. But such a system is usually installed to service large cottages, enterprises, hotels and other institutions, for family use you can do with a 250-300 liter appliance.
According to the shape of the tank:
- Horizontal - It takes up a lot of space, but it is easier to independently maintain the desired water level in it without resorting to connecting pumps.
- Vertical - saves free space, but is very limited in capacity.
Depending on the nuances of use, the features of the layout and the availability of free space, you can choose the optimal BKN model that will organically fit into the design of the room and provide your home with an uninterrupted supply of hot water.
What to look for when choosing a BKN
One of the main parameters that should be the decisive argument when buying a boiler is its capacity. To find out the required tank capacity, we recommend that you focus on the number of people in your family.
Displacement recommendations:
- 80-100 l - 2 consumers;
- 100-120 l - 3 persons;
- 120-150 l - 4 users;
- 150-200 l - 5 consumers.
It is important to separate the concepts of “total tank capacity” and “working capacity”, because a spiral pipe located inside the boiler occupies a significant area. Therefore, be sure to check when buying how much real water is placed in the device. In the technical specifications, this nuance should be indicated.
Also, in addition to the “total” recount of potential consumers, it is necessary to take into account both the frequency and volume of water use. For example, if your family likes to soak in a warm bath rather than taking a quick shower, the working capacity of the tank should be appropriate - at least 120 liters.
It is advantageous to use BKN complete with a solid fuel or single-circuit gas boiler, but if the water consumption is less than 1 l / min, a double-circuit boiler will cost less, which will take much less space than an indirect heating system
Other important parameters:
- Power - the greater the water consumption, the higher should be the resource of the device. But at the same time, it is important that the power of the "indirect" does not exceed the capacity of the heating system (or other external energy source). For example, if the volume of the storage tank varies between 120-150 liters, the boiler power should be at least 23 kW, and for 160-200 liters, 31-39 kW will already be needed.
- Heating time - a parameter depending on the volume of the tank and the number of turns on the coil (large or combined containers can be equipped with several spirals).
- Tank material - for long-term use, stainless steel or medical steel boilers are best suited.
- Thermal insulation - in cheap models, foam rubber is used, which quickly wears out and transmits heat, so it is better to purchase a more expensive device that used polyurethane.
- Control - the device will be able to work in automatic mode, if necessary, turning off and starting the current of water, to control the heating using a temperature sensor.
When choosing the shape and size of the tank, it is also necessary to take into account that although theoretically the boiler can be installed in any room where there is access to the heating main, its optimal location is next to the boiler. So heat transfer is most efficient.
Indirect heating boiler can be made by hand. Instructions for the manufacture of the unit are described in this article.
Nuances and boiler connection schemes
As already mentioned, BKN uses the energy of an external source to heat water. Therefore, before connecting to a coolant, it is important to choose a suitable circuit for mounting the device. Consider the most common options.
General principles for installing the device
It is necessary to mount the boiler on a prepared, level surface in the immediate vicinity of the boiler. Suspended models are mounted on a concrete or brick wall, at the same level or slightly higher than the boiler.
For an outdoor appliance - level the area reserved for placing the tank (if the floor is critically uneven, you can make a stand in the form of a podium).
The BKN strapping itself is designed to connect the device to two systems - water supply and heating. For this, there are special nozzles on the body.
The safety group of the indirect heating boiler includes check and relief valves that protect the system from high pressure and leakage of hot water
Accession Principles:
- Cold water from the drainage system should enter the lower part of the tank, and hot water should exit the upper part.
- A check valve should be installed at the inlet of cold water, which will prevent the leakage of hot flow from the boiler in the event of a decrease in pressure in the system.
- In the middle of the device, a point for recirculation can be located.
- When the heating circuit is switched on, the coolant must move from top to bottom. That is, a pipe with hot water enters the upper pipe, and a pipe with a cooled one comes out from below.
- All nozzles must be equipped with taps with union nuts to ensure that the boiler can be switched off, for example, in case of replacement of the device or repair work.
Thanks to this scheme, the maximum efficiency of the device is achieved, since the coolant circulating in the coil heats the water in the upper part of the tank, transfers the remaining heat to the low-temperature layers and enters the boiler for new heating.
Schemes of connecting BKN to the source
In order to choose the right scheme for connecting the boiler to the heating system, it is necessary to take into account the possibilities of the existing wiring and the installation location of the heating device. There are several solutions.
Option 1. The most common scheme for constant use of hot water is a connection through a three-way valve. It assumes the presence of two heating circuits - the main and separate for BKN.
To do this, a circulation pump crashes into the hot water supply, and after it a three-way valve is installed, which is controlled by the boiler thermostat.
The scheme works as follows: when the water temperature in the boiler drops below a predetermined mark, the valve switches the system to heat the storage tank at the signal of the thermostat, and after reaching the desired value, it sends the flow to circulate along the common house circuit.
For the three-way circuit to work correctly, it is important to adjust the thermostat data so that the temperature programmed for the boiler is not set lower than in the boiler thermostat (+)
Option 2. Installing a dual pump system - it is advisable to use the scheme if there is no need for constant and large volumes of hot water. For example, a boiler is installed in a country house and is used only on weekends.
In this case, the BKN and the heating boiler are connected in parallel, and the coolant flows will move along two highways. For the forced movement of water, two pumps are installed: on the heating circuit and the supply pipe for the boiler.
Heating is carried out using a thermostat, which temporarily turns off radiator heating, directing the entire system resource to the boiler.
According to the two-nanos scheme, the heating circuit will be switched off for the duration of the boiler’s operation, but in those 30-60 minutes that are necessary to heat the tank from scratch, the radiators will not have time to cool critically (+)
Option 3. For rooms where a multi-circuit heating system is used, for example, in addition to radiators, a warm floor is installed, a hydraulic distributor is used.
Hydroarrows redistribute pressure in individual sections of the circuit and ensure uninterrupted movement of the coolant even without the help of circulation pumps.
Without engineering experience, such a complex scheme is unlikely to be done on its own - in order to provide for a lot of nuances and establish smooth operation of the system, it is better to contact professional designers (+)
Without a hydrocollector in a multi-circuit system, pumping equipment can fail and even heat stroke can occur with damage to radiators.
Return Circulation System
If the boiler has a third input, a recirculation system can be connected to it. To do this, a loopback loop is started at the recirculation point on the device body.
The water flow is in constant motion due to the operation of the circulation pump, so it instantly delivers warm water to the point of consumption (+)
To implement the scheme, you need to mount an additional circuit and install the following elements:
- Check valve at the inlet to the heater.
- Automatic air ventprotecting the pump from air ingress before starting.
- Safety valvewhich will protect against pressure drops.
- Diaphragm expansion tank, in which excess water will flow away with increasing pressure in the system. Note that the capacity of the reserve capacity must be at least 1/10 of the volume of the BKN itself.
If the branch pipe for the recirculation circuit is not provided in the device of the indirect heating boiler, it is possible to insert the return line into the cold water pipe and install the pump. Then the connection is carried out according to the scheme below.
The choice of strapping scheme with or without recirculation should be based on the design of the BKN and heating system, as well as the power of the equipment (+)
Connection according to the return circuit ensures an uninterrupted supply of hot water - that is, you will not need to wait until the coolant warms up the water in the tank.
Before deciding to purchase and install a new water heater in the house, we suggest studying video materials that clearly demonstrate the advantages of the “indirect man” and the nuances of connecting it.
In this video you can find out how indirect heating boilers work with a coolant located inside the coil:
All the nuances of the internal structure and the principles of operation of various types of indirect heating boilers in a detailed video-educational program from a practicing master:
Overview and connection of a 300 liter device that runs on two coolants - a boiler and solar panels:
A detailed analysis of the BKN device and its connection schemes. Practical tips and tricks from the wizard:
As for maintenance, the indirect heating boiler is a fairly unpretentious equipment. With proper installation and smooth operation of the system, you may only need to replace the magnesium anode every 6-12 months and preventive flushing of the tank.
The frequency of service depends on the quality of tap water and the intensity of use. But if you have installed a device that works on the "tank in tank" technology, which has a self-cleaning function, you will not need to change the consumable.
However, you can always agree on regular maintenance of equipment with the craftsmen specializing in the installation and repair of water supply systems.
Have a question? Or is there a desire to share personal experience in choosing, connecting and using an indirect heating boiler? Please leave comments on this article.